University of Rhode Island

Picture of Library

[an error occurred while processing this directive]

   
[an error occurred while processing this directive]
University Libraries
Faculty Publications
Compiled by Margaret J. Keefe

Faculty Publications 1991

ENGINEERING
Mechanical Engineering & Applied Mechanics

Asaba, Makoto, Yukata Asako, Hiroshi Nakamura and Mohammed Faghri. "Numerical Solution of Convection Diffusion Problems in Irregular Domains Mapped onto a Circle." Journal of Thermophysical Heat Transfer. 5(l):103 109. January 1991.

Asako, Y., H. Nakamuro, Z. Chen and M. Faghri. "Numerical Analysis of Two Dimensional Transient Freezing in a Speroidal Capsule." Journal of Heat Transfer. 113(4):1017 1020. 1991.

Asako, Y and Mohammed Faghri. "Parametric Study of Turbulent ThreeDimensional Heat Transfer of Arrays of Heated Blocks Encountered in Electronic Equipment."  IN: National Heat Transfer Conference (28th. 1991. Minneapolis, Minn.) Heat Transfer in Electronic Equipment, 1991. Edited by A. Ortega, D. Agonafar and B. W. Webb. American Society of Mechanical Engineers. (HTD Series v. 171) 1991.  p.135-141.

Asako, Y., and H. Nakamuro, Z. Chen and M. Faghri. "3-Dimensional Laminar Natural Convection in an Inclined Air Slot With Hexagonal Honeycomb Core." Journal of Heat Transfer. 113(4):906-911. 1991.

Asako, Yukata, Hiroshi Nakamura, Yoshiyuka Yamaguchi and Mohammad Faghri. "Three Dimensional Natural Convection in a Certical Porous Layer With a Hexagonal Honeycomb Core."  IN: Proceedings of the Third ASMEZJSME Thermal Engineering Joint Conference. Part 4. ASME. 1991.  p.197-202.

Core, Karen Lynn. Heat Transfer and Population Characteristic in Multinhase Dispersal Media With Phase Discharge. UMI (Theses - North Carolina State University, 1990) 1991.  87p.

Datseris, Philip S.  SEE Wiesner III, Albert F.; Yang, B.

Dunbar, William R., N. Lior and R. A. Gaggioli. "The Component Equations of Energy."  IN: Analysis of Thermal and Energy Systems: Proceedings of the International Conference, Athens, Greece, June 3-6. 1991, Edited by D. A. Kouremenos, G. Tsatsaronis and C. D. Rakopoulus. Greg. Foundas, Technical and Scientific Editions. 1991.

Faghri, Mohammed.  SEE also: Asaba, Makoto; Asako, Y.

Faghri, M., A. Ray, S. Sridar and R. Schmidt. "Entrance Heat Transfer Correlation for Air Cooling Arrays of Rectangular Blocks."  IN: Heat Transfer Enhancement in Electronic Cooling.... Edited by S. H. Bavani and M. Grenier. ASME. (HTD Series Vol.183) 1991.  p.1923.

Florio, John, Jr., Jack B. Henderson, Frederick L. Test and Ramamurthy Hariharan. "Characterization of Forced Convection Heat Transfer in Decomposing, Glass-Filled Polymer Composites." Journal of Composite Materials. 25(l):1515-1539. November 1991.

Florio, John, Jr., Jack B. Henderson, Frederick L. Test and Ramamurthy Hariharan. "A Study of the Effects of the Assumption of Local-Thermal Equilibrium on the Overall Thermally Induced Response of a Decomposing, Glass-Filled Polymer Composite." International Journal of Heat and Mass Transfer. 34(l):135-147. January 1991.

Ghonem, Hamouda.  SEE also: Zheng, D.

Ghonem, H., A, Pineau and T. Nicholas. "Analysis of Elevated Temperature Fatigue Crack Growth Mechanisms in Alloy 718." IN: American Society of Mechanical Engineers. Winter Meeting. (1991. Atlanta, Ga.) Creep-Fatigue Interaction at High Temperature.... Edited by George K. Haritos and 0. 0. Ochoa. ASME. (AD Series Vol.21) 1991.  p.1-18.

Ghonem, H. and D. Zheng. "Characterization of EnvironmentallyDominated Fatigue Crack Growth in Alloy 718 at 6500 C."  IN: Proceedings of the International Symposium on Superalloy 718, 625 and Various Derivitives. Ed. by E. Loria. ASME Publications. 1991.   p.477-490.

Ghonem, H. and D. Zheng. "Environmentally-Dominated Crack Growth Model for Alloy 718."  IN: Mechanical Behavior of MaterialsVI:Proceedings of the Sixth International Conference, Kyoto, Japan, 29- July 2 August 1991, Edited by Masahiro Jono, Tatsuo Inoue. Pergamon. 1991.  Vol.4.

Ghonem, H. and R. Foerch. "Frequency Effects on Fatigue Crack Growth Behavior in a Near Alpha Titanium Alloy." Materials Science and Engineering. A: Structural Material Properties Microstructure and Processing. 138(l):69-81. 1991.

Ghonem, H. and D. Zheng. Mechanisms and Modelling of Environment-Dominated Fatigue Crack Growth in a Nickel Based Superalloy. Final Report, 1989-1991. University of Rhode Island, Dept. of Mechanical Engineering and Applied Mechanics. (AD-A253967; URI-MSL-921; AFOSR-92-0787TR) 1991.  252p.

Ghonem, H. and D. Zheng. "Oxidation Assisted Fatigue Crack Growth in Alloy 718 - Part I. Quantitative Modeling." Fatigue & Fracture Engineering Materials and Structure. 14(7):749-760. 1991.

Ghonem, H. and M. Zheng. "Prediction of Fatigue Crack Growth Under Single Overload Application in Ti-6A1-4V." Fatigue & Fracture Engineering Materials and Structure. 14(8):805-814. 1991.

Henderson, Jack B.  SEE: Florio, John Jr.

Horii, K., Y. Matsumae, X.Cheng, M. Takei, B. Hashimoto and T. J. Kim. "Developments of a New Mixing Nozzle for High Pressure Abrasive Waterjet Applications."  IN: 10th International symposium (Amsterdam, The Netherlands, 31 October -2 November, 1990.) D. Saunders, Editor; Organized and Sponsored by the BHR Group Lab. Elsevier. 1991. p.193-206.

Horii, K., Y. Matsumae, X. Cheng, M. Takei, X. M. Cheng, H. Shoda, B. Hashimoto and T. J. Kim. "A Newly Developed Spiral Nozzle for Abrasive Acceleration in Jet Cutting Applications."  IN: Proceedings of the 6th American Water Jet Conference, August 24-27, 1991, Houston Texas, Edited by Thomas J. Labus. Water Technology Association. 1991. p.457-471.

Jouaneh, Musa.  SEE also: Srinivasa, N.

Jouaneh, M. K. "Linking Geometric Models With Analysis of System Behavior."  IN: ASEE Annual Conference (1991. University of New Orleans). Challenges of a Changing World; Proceedings, 1991 Annual Conference, June 16-19, 1991. The Society 1991.  p.33-338.

Kim, Thomas J.  SEE: Horii, K.; Truchot, Patrick; Zheng, Jiyve.

Lefebvre, P. J. and F. M. White. ""Further Experiments on Transition to Turbulence in Constant-Acceleration Pipe Flow." Journal of Fluids Engineering. 113(2):223-227. June 1991.

Narendran, Nadarajah, Arun Shukla and Stephen Letcher. "Application of Fiber Optic Sensors to Fracture Mechanics Problems." Engineering Fracture Mechanics. 38(6):491-498. 1991.

Narendran, N., Arun Shukla and S. V. Letcher. "Determination of Fracture Parameters Using Embedded Fiber Optic Sensors." Experimental Mechanics. 31(4):360-365. December 1991.

Patton, A. "Automotive Vehicle Fires: Government Standards and Litigation." Journal of Trial Diplomacy. 14(l): 1991.

Patton, Alexander J. Fire Litigation Sourcebook. Garland Law Publishing. 1986  (Looseleaf)

Prakash, V. and A. Shukla. "Dynamic Load Transfer in Virgin and Damaged Granular Rock Media." Journal of Engineering Mechanics. 117(3):498-512. March 1991.

Sadd, Martin H.  SEE: Shukla, Arun; Silva, Armand J., Zhu, C. Y.

Shukla, Arun.  SEE also: Narendran, Nadarajah; Prakash, V.; Zhu, C. Y.

Shukla, Arun. "Dynamic Photoelastic Studies of Wave Propagation in Antigranulocytes Media." Optics and Lasers in Engineering. 14(3): 165-184. 1991.

Shukla, Arun and Sanjeev K. Khanna. "Effect of Fiber Matrix Interface on Toughening Mechanisms During Dynamic Fracture of Fiber Reinforced Materials." IN: American Society of Mechanical Engineers, Winter Meeting (1991. Atlanta, Ga.). Experiments in Micromechanics of Failure Resistant Materials.... ASME. (AMD Series Vol.130) 1991.  p.91-103.

Shukla, A., M. Sadd, Y. Xu. and Q. M. Tai. "Experimental and Computational Studies of the Effect of Wave Length on Propagation."  IN: International Conference on Computational Methods and Experimental Measurements (5th. 1991. Montreal, Quebec). Computational Methods and Experimental Measurements. Editors, A. Souse, C. A. Brebba and G. M. Carlomagno. Computational Mechanics Publications. 1991. p. 647-660.

Silva, A. J., W. M. Tian, X. H. Sadd and H. G. Brandes. "Creep Behavior of Fine-Grained Ocean Sediments."  IN: International Conferenc6c for Computer Methods and Advances in Geomechanics (7th. 1991. Cairns, Australia). Proceedings..., Edited by G. Beer, J. R. Booker & J. P. Carter. A. A. Balkema. 1991. p.1-6.

Srinivasa, N. and M. Jouaneh. "Investigation of Surface Roughness Characterization Using an ART2 Neural Network."  IN: American society of Mechanical Engineers. Winter Meeting (1991, Atlanta, Ga.). sensors, controls, and Quality Issues in Manufacturing;.... Edited by T. I. Liu, C. H. Meng, N. H. Chao. ASME. (PED Series v.55) 1991. p.307-318.

Taggart, David G. and Jaychandar Muthu. "Effect of Interface Properties on the Elastic Response of Unidirectional Fiber Composities."  IN: International SAMPE Technical Conference Materials/Affordable Processes.... Edited by Robert L. Carri, Leonard M. Poveromo and Judith Bauland. SAMPE. 1991.  p.341-351.

Taggart, D. G. and J. L. Bassani. "Elastic Plastic Behavior of Particle Reinforced Composites - Influence of Residual Stresses." Mechanics of Materials. 12(l):63-80. August 1991.

Test, Frederick L.  SEE: Florio, John, Jr.

Truchot, Patrick, Pascal Mellinger, Robert Duchamp, Thomas J. Kim and R. Ocampo. "Development of a Cryogenic Waterjet Technique for Biomaterial Processing Applications."  IN: Proceedings of the 6th American Water Jet Conference, August 24-27, 1991, Houston Texas, Edited by Thomas J. Labus. Water Technology Association. 1991.  p.473-480.

Viets, H. "A Combined Undergraduate Program in Engineering and German."  IN: Proceedings of the 1990 Frontiers in Education Conference, Vienna, Austria, July 1990. ASEE.

White, Frank M.  SEE also: Lefebvre, P. J.

White, F. M. and K. Kamemoto, eds. ASME/JSMA Fluids Engineering Conference Ust 1991. Portland, Or.) General Topics in Fluids Engineering, 1991: Presented at the First ASME/JSME Fluids Engineering Conference, Portland, Oregon. June 23-27, 1991. American Society of Mechanical Engineers. (FED Vol.107)1991.  145p.

White, F. M., ed. General Papers in Fluids Engineering, 1991; Presented at the Winter Annual Meeting of the American Society of Mechanical Engineers, Atlanta, Ga. American Society of Mechanical Engineers. (FED Vol.127) 1991. 65p.

White, Frank M. Heat and Mass Transfer. (Rev. ed.] Addison Wesley. 1991. (Rev. ed. of Heat Transfer. 1984)

White, Frank M. Viscous Fluid Flow. 2d ed. McGraw Hill. 1991.  614p.

Wiesner III, Albert F. and Philip Datseris. Apparatus and Method for Finishing Chain Assembly. US 5058252. October 1991.

Wilson, M. P., Jr. "Historical Perspective."  IN: Flow Measurement: Practical Guides for Measurement and Control, D. W. Spitzer, Editor. Instrument Society of America. 1991.

Yang, B., P. Datseris, U. Datta and J. Kowalski. "An Integrated System for Design of Mechanisms by an Expert System Domes: Applications." Journal of Mechanical Design. 113(l):25-31. March 1991.

Zheng, D. and H. Ghonem. "Oxidation Assisted Fatigue Crack Growth Behavior in Alloy 718 - Part II. Applications." Fatigue & Fracture Engineering Materials and Structures. 14(7):761-768. 1991.

Zheng, Jiyue, Richard Heines and Thomas J. Kim. "Characterization of Energy Dissipation Phenomenon in Abrasive Waterjet Cutting." 

White, Frank X. Heat and Mass Transfer. (Rev. ed.] Addison‑Wesley.1991. (Rev. ed. of Heat Transfer. 1984)

White, Frank X. Viscous Fluid Flow. 2d ed. McGraw Hill. 1991. 614p.

Wilson, M. P., Jr. "Historical Perspective."  IN: Flow Measurement: Practical Guides for Measurement and Control, D. W. Spitzer, Editor. Instrument Society of America. 1991.

Yang, B., P. Datseris, U. Datta and J. Kowalski. "An Integrated System for Design of Mechanisms by an Expert System‑Domes: Applications." Journal of Mechanical Design. 113(l):25‑31. March 1991.

Zheng, D. and H. Ghonem. "Oxidation‑Assisted Fatigue Crack Growth Behavior in Alloy 718 ‑ Part II. Applications." ' Fatigue & Fracture Engineering Materials and Structures. 14(7):761‑768. 1991.

Zheng, Jiyue, Richard Heines and Thomas J. Kim. "Characterization of Energy Dissipation Phenomenon in Abrasive Waterjet Cutting "  IN: Proceedings of the 6th American Water Jet Conference, Aug st ~4‑27, 1991, Houston Texas, Edited by Thomas J. Labus. Water Technology Association. 1991. p.163‑177.

Zheng , Jiyue and Thomas J. Kim. "Material Removal of Polycrystalline Ceramics by a High‑Pressure Abrasive Water Jet ‑ A Sem Study.* International Journal of Water Jet Technology. 1(2):6571. September 1991.

Zheng, J. and Thomas J. Kim "A Study of Brittle Erosion Mechanism Applied to Abrasive Waterjet Processes."  IN: 10th International Symposium (Amsterdam, The Netherlands, 31 October ‑ 2 November, 1990.) C. Saunders, Editor; Organized and Sponsored by the BHR Group Lab. Elsevier. 1991. p.115‑133.

Zhu, C. Y., R. Chona and A. Shukla. "Influence of Singularity Dominated Zone for Propagating Cracks in Finite Size Specimens." Theoretical and Applied Fracture Mechanics. 16(2):167‑177. 1991.

Zhu, C. Y., A. Shukla and M. H. Sadd. "Prediction of Dynamic Contact Loads in Granular Assemblies." Journal of Applied Mechanics. 58(2):341‑346. June 1991.

Zheng , Jiyue and Thomas J. Kim. "Material Removal of Polycrystalline Ceramics by a High Pressure Abrasive Water Jet - A Sem Study.* International Journal of Water Jet Technology. 1(2):6571. September 1991.

Zheng, J. and Thomas J. Kim. "A Study of Brittle Erosion Mechanism Applied to Abrasive Waterjet Processes." IN 10th International Symposium (Amsterdam, The Netherlands, 31 October 2 November, 1990.) C. Saunders, Editor; Organized and Sponsored by the BHR Group Lab. Elsevier. 1991.  p.115-133.

Zhu, C. Y., R. Chona and A. Shukla. "Influence of Singularity Dominated Zone for Propagating Cracks in Finite size Specimens." Theoretical and Applied Fracture Mechanics. 16(2):167-177. 1991.

Zhu, C. Y., A. Shukla and M. H. Sadd. "Prediction of Dynamic Contact Loads in Granular Assemblies." Journal of Applied Mechanics. 58(2):341-346. June 1991.


Return to Faculty Publications 1991 Table of Contents.
Return to Faculty Publications homepage.